1. Product photo 2. Product Feature 1 ） Product supply voltage is 3V(AAA*2) 2 ） Adopt 2.4G wireless control, with feature of long distance and non-directional control 3 ） Full keys design, unique interface, simple operation 4 ） Multi zone control function simple: could control single zone or...
1. Product photo
2. Product Feature
1）Product supply voltage is 3V(AAA*2)
2）Adopt 2.4G wireless control, with feature of long distance and non-directional control
3）Full keys design, unique interface, simple operation
4）Multi zone control function simple: could control single zone or overall zones; controlled area indicated by indicator light , more intuitive
5）Hanging storage way, more easy to access and storage
6）Two ways for accessories installation, flexible choice
7）Two Colors: Black/White
8）RFBK-DIM-2.4G match with HD series dimming driver
9）Three years warranty
3. Technical Parameters
Sleep power consumption
Emission power consumption
Remote control rack, 3M foam sponge glue, M4 double-headed self-tapping screws, φ6 expansion tube, battery, manual
4. Direction for use
Each buttons function as below:
Name of key
ON in any time
OFF in any time
3 Brightness Grades：20%, 50%, 100%;
decrease light brightness, long press continuously
Increase light brightness, long press continuously
CW balance key
Zone selection key
Select control zone（selected zone indication light will on, support single zone and overall zones control）
Remark：Short press Zone Key, for single zone shift, selected zone indication light on. Long press Zone key for 3 seconds, select allover zones, 4 indication lights on in the meantime, control allover area lights.
Multi-zone remote control need to set the zone before using, that means match each driver to the corresponding group.
Matching Zone operation
Step 1：Connect the driver with load LED(Without power on)
Step 2：Select Zone（Through pressing“Zone”key to light on the selected zone indication light）;
Step 3：Pressing “Mode Key” and hold on, power on the driver，the load LEDs will be 50% brightness as responding to enter match code/clear code state（Notice：Step 3 should be finished within 8 seconds after Step 2, indication light will off if no operation within 8 seconds）;
Step 4：Continuously to press the key “On” for 3 times within 5 seconds after step 3（the brightness of LEDs will change from 25%-10%-back to preset level as responding）;
If match code unsuccessfully, please re-operate above steps（Notice：“Power on driver to enter match code/clear code state” should after at least 10 seconds from the last time power off）.
Clear code operation
Clear code between the driver and remote control is for backing to factory default.
After clear code successfully, the driver can be controlled by anyone the same model remote control or the remote control not the same model but compatible with each other.
Step 1: Connect the driver with load LED(Without power on)
Step 2: Pressing the key “Mode” and power on the driver, the load LEDs will be 50% brightness white as responding. Means entered the learning code/ clear code status successfully(No need to select the zone, remote control in any zone status can be used to clear code for drivers in any zones)
Step 3:Continuously to press the key “Brightness -” for 3 times within 5 seconds after step 2, the brightness of LEDs will change from 25%-10%-back to preset level. Code clearing successfully
If not, please re-operate from step 1 to 4.（Notice: Power on again the driver to enter the code learning status should be 10s after last power-down）. Anyone the same model remote control or the remote control not the same model but compatible with each other can be used to clear code.
1）Each driver can save 4 different RF codes ( it means each driver can be controlled by 4 different-code remote in the Max).If there is confusion,, more remote control all can control, you need to clear the code and then use the specified remote control re-code with the driver.
2）Anyone the same model remote control or the remote control not the same model but compatible with each other can be used to clear code.
5. Remote control accessories installation instructions
1）Remote control accessories list as below:
Remote control rack 1pc
|3M foam sponge glue 1pc|
|M4 double-headed self-tapping screw 1pc||φ6 expansion tube 1pc|
2）Remote control rack installation instructions:
There are two different installation methods for the remote control rack, customers can choose to install according to the different situation;
The first installation method: free drilling installation (for flat no ash surface)
（1）First, tear off the protective film for one side of 3M foam sponge glue, then affixed it on the behind circle of the remote control rack;
（2）Tear off the protective film for other side of 3M foam sponge glue, and stick the remote control rack on the place where you want to stick.
（3）Hang the remote control on the rack after installation
The second installation method: free drilling installation(suitable for uneven and ash surface)
(1) Drill a hole on the wall with a 6mm drill bit;
(2) Install the φ6 expansion tube in the hole;
(3)Twist the tip end of the M4 double-headed self-tapping screw into the expansion tube;
(4) Install the remote control rack on the screw like below
(5) Hang the remote control on the rack after installation